油墨特性：

主要用于ABS、PC、PVC、PS等，具有高色澤、高色彩、高遮蓋力、高穩定性、耐酒精及特慢干之特點。（可在30分鐘內不需開油洗網）

印刷：選用網目為250- 400目，絲印移印均可。

表干及實干時間：表干時間自然揮發5-10分鐘；實干時間在24小時以內，如需快速干燥請烘烤50度20分鐘為效果。

稀釋及清洗：783慢干開油水；同時可使用718洗網水清洗。

測試方法（完全干燥后）：

1、3M膠紙粘在畫有百格的油墨表面，45度角迅速拉起不脫油;

2、純度99%的酒精，500克砝碼用棉布包住在油墨表面，以水平力來回拉100次無脫色。

使用方法：

1、使用前應充分?jǐn)嚢?，用后隨時封閉；

2、攪拌時加開油水10-15%，稀釋到印刷粘度；

3、網板塞網時可用洗網水清洗；

4、不得與其它類型油墨混合使用。

注意事項：

1、塑膠材料的外觀相似，但可能會是不同的材料，客戶需試印確定其符合要求后，再批量印刷；

2、在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可；

3、環境溫度過高，將會影響油墨原有質量；

4、根據氣候變化，請遠離火源，陰暗環境下存放。

Ink characteristics: mainly used for ABS, PC, PVC, PS, etc, with the high colour and lustre, high color, high covering power, high stability, resistant to alcohol and slow the characteristics, dry. (can be in 30 minutes don't need to open oil washing nets) printing: choose the mesh is 250-400 mesh, silk screen moving printing all can. Table dry and work time: dry time table natural volatilize 5-10 minutes; Work in time within 24 hours, if need to rapid drying please baking 50 degrees 20 minutes for the best effect. Dilution and cleaning: 783 slow oil and water do open; At the same time, you can use clean water to wash the nets 718. Test method (dry) : 1, 3 M tape is stuck in the picture has the case of printing ink surface, 45 degree Angle quickly pull up not to take off the oil; 2 and purity, 99 ? and ? ? alcohol, 500 grams of Jordan farmar cover with cotton cloth in ink surface, with the level force and 100 times back and forth without decoloring. Method of use: 1, before the use should be fully mixing, after using closed at any time; 2 when the oil and water, stir number 10-15 ? F ? ? dilution to printing viscosity; 3, sheet stuffed nets can be used when washing nets water cleaning; 4, not with other kinds of printing ink mixed use. Note: 1, the appearance of the plastic material similar, but may be different materials, the customer shall determine the ShiYin requirements after another, batch printing; 2, in moving printing process, such as a wire drawing or leave, can be appropriately to add some slow dry paste can